Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - jsaw

Pages: [1]
1
AI use in Regional Simulation (BRAILS) / Re: "The bbox seems to be outside of the US. Footprints probably only exist in OSM"
« on: May 19, 2021, 10:07:14 PM »
Thanks for the reply! And sorry, I should have been clearer. I meant that the bbox I specified *is* within the US, but I still get this message. Should I be concerned?

2
AI use in Regional Simulation (BRAILS) / "The bbox seems to be outside of the US. Footprints probably only exist in OSM"
« on: May 19, 2021, 09:49:05 PM »
When I specify the coordinates of the bounding box, I get "The bbox seems to be outside of the US. Footprints probably only exist in OSM". I still do get the desired buildings within the bounding box, though. What could be causing this error message? Should I be worried that I get this error message? Thank you!

3
AI use in Regional Simulation (BRAILS) / Re: matching "geometry" to images
« on: April 15, 2021, 05:42:31 AM »
Thank you!

4
AI use in Regional Simulation (BRAILS) / Re: matching "geometry" to images
« on: April 15, 2021, 02:40:27 AM »
Thank you again for the reply.

After doing pip install BRAILS --upgrade, I now get the following error. Please let me know what I can do to fix this. Thank you!

5
AI use in Regional Simulation (BRAILS) / matching "geometry" to images
« on: April 14, 2021, 11:15:59 PM »
I'm having trouble matching the results (from the BIM table) to the images saved in the TopView and StreetView folders. I have a few questions:

  • The longitude/latitude specified in the BIM table doesn't exactly match the names of the TopView and StreetView images. Is this because the BIM table specifies the centroid coordinates of the building, whereas the TopView and StreetView images are named by the coordinates of the location at which the photo was taken?
  • What is the recommended way for quickly matching the entry in the BIM table to the images? Should I just manually look for the images with the coordinates that are closest to the coordinates in the BIM table?
  • There are 11 buildings listed on the table (ID 0 through 10), but there are 21 images in each folder. Some buildings seem to have three images each, while others have one image each. Is there a systematic way that the number of images is assigned to each building?


6
AI use in Regional Simulation (BRAILS) / Re: pip install BRAILS
« on: April 14, 2021, 11:01:31 PM »
Thank you again for the help! Yes, I had to install Microsoft Visual C++ 14.0.

7
AI use in Regional Simulation (BRAILS) / Re: pip install BRAILS
« on: April 14, 2021, 05:39:23 AM »
Thank you, I was able to get pip install BRAILS to work.

I still have a problem, where BRAILS seems to have been installed but BRAILS modules are not found. (screenshot below) What might be the issue here?

8
AI use in Regional Simulation (BRAILS) / Re: pip install BRAILS taking too long
« on: April 13, 2021, 10:56:14 PM »
Hello, this is what I get:

9
AI use in Regional Simulation (BRAILS) / pip install BRAILS
« on: April 13, 2021, 04:24:12 PM »
Hello, I'm currently having difficulties installing BRAILS. I have Python 3.7.6 so I downloaded Fiona-1.8.18-cp37-cp37m-win_amd64.whl and GDAL-3.2.2-cp37-cp37m-win_amd64.whl. However, the pip install BRAILS is taking too long/running into an error. What might be the issues causing this problem? Thank you in advance!

(posted earlier in forum post "Queries about BRAILS installation")

10
AI use in Regional Simulation (BRAILS) / Re: Queries about BRAILS installation
« on: April 11, 2021, 05:10:35 AM »
Hello, I'm currently having difficulties installing BRAILS. I have Python 3.7.6 so I downloaded Fiona-1.8.18-cp37-cp37m-win_amd64.whl and GDAL-3.2.2-cp37-cp37m-win_amd64.whl. However, the pip install BRAILS is taking a very long time. What might be the issues causing this problem? Thank you in advance!

11
AI use in Regional Simulation (BRAILS) / Where are the building images saved?
« on: April 05, 2021, 01:44:16 AM »
Is there a way for me to save the building images (satellite, street view) that BRAILS uses to create its building inventory? Put in another way, where can I locate the images that correspond to each row in the BIM file? Thank you!

12
AI use in Regional Simulation (BRAILS) / Re: UnidentifiedImageError
« on: March 31, 2021, 01:34:47 AM »
Thank you! Example 2 finally works, but I'm now getting the error with Example 3. Do you think there's still an issue with my maps api?

13
AI use in Regional Simulation (BRAILS) / UnidentifiedImageError
« on: March 30, 2021, 10:45:12 PM »
I'm currently experiencing an UnindentifiedImageError when running example 2. I'm quite sure that my GoogleMapsApiKey is correct (Maps Embed API has been enabled). Do you have any suggestions for what else could be causing this error? It would be helpful to know if there are a few things I can double-check to make sure I'm doing this correctly. Thank you!

14
AI use in Regional Simulation (BRAILS) / Re: Timeout error when running Example 2
« on: March 30, 2021, 04:58:35 AM »
Thank you!

I'm actually now running into a "cannot identify image file" error. But I'm using the same api key, so I don't think the api key is incorrect. Do you have any suggestions?

15
AI use in Regional Simulation (BRAILS) / Timeout error when running Example 2
« on: March 29, 2021, 07:51:07 PM »
I'm currently running into a time-out error when trying to run Example 2 in the BRAILS demo, shown in the screenshot attached. Please let me know how I can fix this, thank you!

Pages: [1]